BITULIGHT P is a prefabricated ELASTOMERIC-PLASTOMERIC membrane offering good performance, by virtue of a higher percentage of polymers such as POLYPROPYLENE (APP) and POLYOLEFIN (APAO). Its special…
BITULIGHT P is a prefabricated ELASTOMERIC-PLASTOMERIC membrane offering good…
ADVANTAGES: Produced without the use of fossil resources and packed in recycled plastic cartridges to reduce environmental impact Solvent-free, with very low emission of Volatile Organic Compounds…
ADVANTAGES: Produced without the use of fossil resources and packed in recycled…
Planiprep Fix is an ultra-fast drying, fine-grained, thixotropic, cementitious skimcoat compound for the repair and levelling of interior substrates, including, floors and steps. Planiprep Fix can be…
Planiprep Fix is an ultra-fast drying, fine-grained, thixotropic, cementitious…
TECHNICAL DATA: Mixing ratio: comp. A: comp. B = 10:1 transparent - 11:1 if coloured. Colour of mix: transparent or coloured. Consistency of mix: fluid. Density of mix (kg/m³): 1,065-1,095. Abrasion…
Two-component, high-performance, highly-deformable, quick-setting and drying cementitious adhesive with no vertical slip and extended open time for ceramic tiles and stone material.
Two-component, high-performance, highly-deformable, quick-setting and drying…
TECHNICAL DATA: Mixing ratio: component A : component B = 80 : 20. Colour of mix: neutral. Consistency of the mix: viscous fluid. Density of mix (kg/m³): 1500. Viscosity of the mix (mPa·s): 1,100 ±…
TECHNICAL DATA: Mixing ratio: component A : component B = 80 : 20. Colour of…
Alkali-resistant glass fibre mesh (in compliance with the ETAG 004 guide) for reinforcing protective waterproofing layers, anti-fracture membranes and thermal insulation systems.
Alkali-resistant glass fibre mesh (in compliance with the ETAG 004 guide) for…
Two component low viscosity epoxy resin for injection. Epojet LV is used to attribute the monolithic nature to cracked structures and for bonding and structural strengthening of concrete and masonry…
Two component low viscosity epoxy resin for injection. Epojet LV is used to…
TECHNICAL DATA: Where to use: on walls for ceramic and natural stone coatings. Workability time: 2-3 hours. Thickness applied: from 2 to 20 mm. Waiting time before laying ceramic and natural stone:…
TECHNICAL DATA: Where to use: on walls for ceramic and natural stone coatings.…
ETA 10/0024 ETA 10/0025 TECHNICAL DATA: Consistency: powder. Colour: grey and white Density of the mix (kg/m³): 1,400. Application temperature range: from +5°C to +35°C. Mixing ratio: 21-24% with…
ETA 10/0024 ETA 10/0025 TECHNICAL DATA: Consistency: powder. Colour: grey and…
TECHNICAL DATA: Recommended mixing ratio: 350-450 kg of MAPECEM for 1 m³ of aggregates (diameter from 0 to 8 mm) and with 80-160 kg of water according to the moisture content of the inerts.…
TECHNICAL DATA: Recommended mixing ratio: 350-450 kg of MAPECEM for 1 m³ of…
Pre-applied, fully bonded, self-adhering, HDPE waterproofing membrane to protect against water underground structures Where to use: Horizontal and vertical waterproofing prior to pouring concrete in…
A high quality elastomeric flat roof waterproofing membrane made of a latest generation distilled bitumen based compound and thermoplastic elastomeric resin (SBS) Where to use: ELASTOSHIELD TS4 AF P…
A high quality elastomeric flat roof waterproofing membrane made of a latest…
Rapid Level CT 3220 is a rapid setting smoothing/levelling compound for levelling differences in thickness between 3mm to 20mm in one application. It allows the installation of ceramic, porcelain and…
Rapid Level CT 3220 is a rapid setting smoothing/levelling compound for…
TECHNICAL DATA: Pot life of mix: 50 minutes. Open time: ≥ 30 minutes. Grouting of joints: – on walls: after 2-3 hours. – on floors: after 2-3 hours. Set to light foot traffic: 2-3 hours. Ready for…
TECHNICAL DATA: Pot life of mix: 50 minutes. Open time: ≥ 30 minutes. Grouting…
