MapePave

PUBLIC SPACES

LANDSCAPING

RESIDENTIAL BUILDINGS

SUITABLE FOR SURFACES USED BY VEHICLES

MapePave Range is intended to make it easier to lay natural and engineered stone pavers all year.

It includes a ready-to-use mortar system (MapePave Mortar and MapePave Slurry) that enables normal setting and regulated shrinkage for fast-drying bedding and installation of 20mm porcelain and natural stone.

MapePave Brush in Grout a single component ready-to-use polybutadiene-based drainage mortar for grouting paved floors with joints at least 5 mm wide.

Products in this line


MapePave Mortar

MapePave Mortar

Pre-blended, ready to use mortar with normal setting and controlled shrinkage for fast-drying bedding. Use in conjunction with MapePave Slurry.
MapePave Mortar is ideal for bedding 20mm porcelain, it is rapid curing (just 12 hours for foot traffic), rapid curing, thin application, with low shrinkage and is compliant with BS 7533. Pre-blended, just mix with water, to be used in conjunction with MapePave Slurry.

WALKABLE AFTER 12 HOURS

Mix ratio

Packaging: 25kg bags.
Consumption 15 kg/m² per cm of thickness.
MapePave Slurry

MapePave Slurry

Pre-blended, ready to use mortar, mixed with water for a paving slurry ideal for bonding 20mm porcelain. Use in conjunction with MapePave Mortar.
MapePave Slurry is a bonding agent to be used in conjunction with MapePave Mortar  for the rapid installation of exterior paving including 20mm porcelain.

WALKABLE AFTER 12 HOURS

Mix Ratio

Packaging: 20kg bags.
Consumption 15 kg/m² per cm of thickness.
MapePave Brush in Grout

MapePave Brush In Grout

One -component ready to-to-use polybutadiene-based drainage mortar for grouting paved floors with joints at least 5mm wide.
Grouting all types of external paved floors (porcelain slabs, cement-based composites, porphyry slabs and blocks, etc.) subject to light traffic (vehicles up to 3.5 tonnes).

JOINTING MORTAR

READY TO USE

LIGHT FOOT TRAFFIC AFTER 24 HOURS

EASY TO APPLY

Packaging: supplied in vacuum-packed 15kg drums.
Consumption depends on the width of the joints and the size of the slabs eg. where 600 x 600 x 20mm slabs are installed with a 5mm joint a 15kg drum of this product will cover approximately 25m .

technical-documentation-wBrochures, manuals, guides

Request a FREE sample 

Sample
Literature
Please select your choices:

News & Events

Mapetherm System repairs & protects external surfaces at historic Broomfield Hospital

April 15, 2024

A Mapetherm System has been used to complete an external surface refurbishment at Broomfield Hospital in Chelmsford, Essex.  The installation for Mid and South Essex NHS Foundation Trust was carried out by C J Driscoll and Ruddick Contractors, for J W Steele & Sons Ltd, with Mapei materials supplied by RendMaster. A further Mapei installation will take place during phase two works.

Originally known as Essex County Hospital, Broomfield opened in 1940 as a tuberculosis centre.  The complex retains an Edwardian manor house and a variety of original sanatorium buildings, along with two areas of woodland and expansive lawned gardens. Today, the hospital is home to the internationally renowned St Andrew's burns and plastics centre and it provides a wide range of services, including A&E, emergency medicine and surgery, elective surgery, maternity and paediatric services.  The surface refurbishment works were carried out in a courtyard area, on a one-sided section of original walling spanning approx. 400m2.  The second installation will include a 450m2 courtyard area and stairwell.

The Mapei specification featured Silancolor Tonachino 1.5mm, a full silicone resin topcoat and Silancolor Base Coat primer, which were both applied over Mapetherm AR1 GG, reinforced with Mapetherm Net and then applied onto Mineral Wool insulation boards, pre-installed by the contractor. Silancolor Tonachino is a water-repellent, breathable siloxane coating product, used to repair and protect internal and external surfaces. It is offered in four granulometries - 0.7 mm, 1.2 mm, 1.5 mm and 2.0 mm - with a 1.5mm grain specified for the hospital application. Silancolor Base Coat is a coloured silicone resin-based primer in water dispersion, with micro granular quartz; it was used to even out the absorption of the substrate and promote bonding of the subsequent topcoat finish on the walls. Mapetherm AR1 GG is a high performance, one component cementitious base coat - for bonding, levelling and reinforcing thermal-insulating panels and thermal insulation systems - and Mapetherm Net is an alkali-resistant glass fibre mesh, ideal for reinforcing skim coats when repairing façades and installing Mapetherm thermal insulation systems.

“The Mapei system helped us achieve a great finish at Broomfield Hospital.  It was easy to use, and it was also a pleasure to work with Mapei’s technical team – they supported the lads on site and were involved every step of the way,” explained Ruddick Contractor’s Director, Kevin Ruddick.

If you would like to be kept up to date with all the developments and industry news from Mapei UK.
Click here to sign up -  https://www.mapei.com/gb/en/newsletter 

Thermal Insulation External Thermal Insulation System protecting Masonry Restoration Products

Products mentioned in the article

SILANCOLOR BASE COAT
SILANCOLOR BASE COAT
TECHNICAL DATA: Consistency: thick liquid. Colour: white or various colours using the ColorMap ® automatic colouring system. Density (EN…
MAPETHERM AR1 GG
MAPETHERM AR1 GG
ETA 10/0024 ETA 10/0025 TECHNICAL DATA: Consistency: powder. Colour: grey and white Density of the mix (kg/m³): 1,400. Application…
MAPETHERM NET
MAPETHERM NET
TECHNICAL DATA: Composition: 100% glass fibre. Colour: white. Mesh size (mm): 4.15 x 3.8. Weight of primed mesh (g/m²): approx. 150.…
SILANCOLOR TONACHINO
SILANCOLOR TONACHINO
TECHNICAL DATA: Consistency: paste. Colour: white or various colours using the ColorMap ® automatic colouring system. Density (EN ISO…

Keep in touch

Subscribe to our newsletter to get Mapei news